Gear Indicator Motorcycle for Yamaha YZF-R1 R6/Fzh150 Fzn150 Xt660 Fz-16 FZ-S Fz1 Xvs950A Midnight Star Fz8 Fz6r Xv1900a 6 Leve

(If you encounter any problems, please contact us first, please do not leave a bad review or raise a dispute first, we will be happy and try our best to help you deal with it, thank you)

About installation:

1. Remove the seat and locate the Speed Sensor coupler.

The Speed Sensor is usually located on the top of the gearbox and reads the revolution of the countershaft.

2.Separate the Speed Sensor coupler (you might need to use a small flathead screwdriver to get the coupler apart). Rotate the wheels while ignition is on.The speedometer should indicate 0. If so, turn the ignition off and proceed to the next step. Otherwise, if the speedometer registers a speed other than 0,you have not disconnected the correct coupler and need to look again.

3. Connect the GIpro Black/Green wire to this bike wire, using the Red wire tap
connector supplied.

4. Connect the GIpro Red wire to a switched +12V wire, e.g. to the rear brake light switch, located under the fuel tank (2-pole brown or black connector,Brown wire at the main wiring harness side). Use the other Red wire tap connector supplied. You may also use e.g. the hot wire of the front parking light.

5. Check whether everything is installed and working properly:
- Select Neutral and turn ignition On~
The GIpro display should count from 6 to 1, then “L” flashes slowly.
(If not, the display is not receiving power and/or ground. Check the
connections at the speed sensor connector and also at the 4-pole plugs.)
- Rotate the wheels ~the display should indicate a rolling wheel.
(If not, the display is not receiving the speed signal. Check the
connection at the speed sensor connector and also at the 4-pole plugs.)
- Start the engine ~“L” should flash faster for a few seconds.
(If not, the display is not receiving the RPM signal. Check the wire tap.)
Turn the ignition Off. If the tests still fail, disconnect the 3-pole and 4-pole
connectors and check whether the connector pins are bent or pushed out of
position. Spray some WD40 into the plugs.

Fitment:

For YAMAHA FZ8{nonABS}(2010-2015)
For YAMAHA Bolt{non-ABS}(2013-2016)
For YAMAHA YZF-R1(1998-2008)
For YAMAHA Bt1100 Bulldog(2002-2006)
For YAMAHA Dlverslon{non-ABS} (2009-2015)
For YAMAHA Dyag Star(1999-2006)
For YAMAHA Fjr1300{non-ABS}(2001-2005
For YAMAHA Fjr1300{ABS}(2003-2005
For YAMAHA Fz-16/FZ-S(2008-2015)
For YAMAHA Fz400(1997-2002)
For YAMAHA Fz6{non-ABS}(1998-2012)
For YAMAHA FZ6r(2009-2016)
For YAMAHA Stryker(2011-2016)
For YAMAHA Fz8{non-ABS}(2010-2015)
For YAMAHA Fz1(2001-2016)
For YAMAHA Fzh150(2015)
For YAMAHA Fzn150(2015)
For YAMAHA Fzs600 Fazer(1998-2003)
For YAMAHA Fzs1000 Fazer(2001-2015)
For YAMAHA Mt-01(2005-2012)
For YAMAHA Mt-03{non-ABS}(2006-2016)
For YAMAHA Ralder(2006-2016)
For YAMAHA Roadllner(2006-2015)
For YAMAHA Road Star(1999-2014)
For YAMAHA Royal Star{All Varlants}(1996-2013)
For YAMAHA V-Star{950cc and above}(All)
For YAMAHA Warrlor(2002-2012)
For YAMAHA Wr250r/x(2008-2016)
For YAMAHA Wr450r/x(2008)
For YAMAHA Xt660(2004-2015)
For YAMAHA Xv1600A wlld star(1999-2005)
For YAMAHA Xvs950A Mldnlght Star(2009-2016)
For YAMAHA Xvs1300A Mldnlght Star(2007-2015)
For YAMAHA Yzf-R6(1998-2016)
For YAMAHA Yzf-R6s(2006-2009)
For YAMAHA Stratollner(2006-2015)
For YAMAHA TDM900{non-ABS}(2002-2013)
For YAMAHA TDM900{ABS}(2002-2006)
For YAMAHA Xj6{non-ABS}(2009-2015)
For YAMAHA Xjr400(2002-2007)
For YAMAHA Xjr1300(2004-2016)
For YAMAHA Xv1900A Mldnlght Star(2006-2015)
For YAMAHA Xvs1100 Drag Star(1999-2006)
For YAMAHA Ys250 Fazer(All)

If you have any questions about this product, you can contact us at any time. It is recommended that you can find our customer service to consult whether the product is suitable for your car before placing an order, and avoid some unnecessary problems.

FAQ

Q: Will we receive products that are not working properly?
A: We will test the product before delivery to ensure it works properly and send a picture to confirm, please rest assured to purchase.

Q: Are all products ready in stock? When is the delivery date?
A: All products that can be paid are in stock and we will ship them within 48 hours after payment.

Q: After receiving the product, how to install it?
A: You can complete the installation through our installation manual, you can also contact our after-sales staff to guide you finish the installation, we are available 24 hours.

Q: Can we return the product if we are not satisfied?
A: We have participated in the free return service. If you are in the United States, Canada, Australia, Britain, France, Spain, Germany, you can enjoy this service.

Q: What are the benefits of becoming a store fan?
A: Follow our NORXI store, get an extra 2% discount on all products, participate in fan activities and enjoy VIP customer service.